ATK Candy 7

This guide will walk you through how to adjust bindings such as the ATK Crest, Freeraider, and other ATK models to your skis, how to set the DIN release value, and how to use the bindings on your tour!

ATK Candy

Adjusting Length

The binding length is adjusted forward and backward using a star screwdriver (PH2). The rear housing should be adjusted so that the included spacer fits between the binding and the boot. Make sure there is no weight on the boot when making this adjustment.

Adjusting the Release Value

The release value is adjusted by turning the silver screw (PH2) at the top of the rear housing. There is a scale on the back of the housing to guide you in adjusting it correctly.

Using Walk Mode

Lock the ski brakes into walk mode using the lever on the right side of the binding. Then, rotate the rear housing 180 degrees so the pins face backward. Step into the front housing with your boot and pull the lever up on the front housing to engage walk mode. Press down on the ski brakes to lock them in walk mode. There are two heel lifters that can be flipped forward for different angles.

Using Ski Mode

Rotate the rear housing so the pins face forward. The brake will then hit the ground. Step into the front housing with your boot. The lever should be in walk mode. Step hard into the rear housing to lock the boot in place.

Attaching Ski Crampons

To attach ski crampons, hold the crampon vertically on either the right or left side of the binding. Slide the crampon into place so it is centered on the ski. Then, lower the crampon flat onto the ski. To remove the crampon, reverse the process.

It’s easiest to attach crampons when you’ve taken your skis off, but with a bit of practice, you can save time and energy by attaching and removing the crampons while still wearing your skis.

ATK Crest

Adjusting Length

Adjust the binding length forward and backward using a star screwdriver (PH2). The rear housing should be adjusted so that the included spacer fits between the binding and the boot. Ensure there is no weight on the boot when making this adjustment.

Adjusting the Release Value

The release value is adjusted by turning the silver screw (PH2) on the top of the rear housing. The release scale is located on the back of the housing.

Using Walk Mode

Lock the ski brakes into walk mode using the lever on the right side of the binding. Rotate the rear housing 180 degrees so the pins face backward. Step into the front housing with your boot and pull the lever up on the front housing to engage walk mode. You can flip the heel lifter forward to use it.

Using Ski Mode

Rotate the rear housing so the pins face forward. Press the lever on the right side of the binding to engage the ski mode. Step into the front housing with your boot. The lever should be in walk mode. Step hard into the rear housing to lock the boot in place.

Attaching Ski Crampons

To attach ski crampons, hold the crampon vertically on either the right or left side of the binding. Slide the crampon into place so it is centered on the ski. Then, lower the crampon flat onto the ski. To remove the crampon, reverse the process.

ATK Freeraider

Adjusting Length

Adjust the binding length forward and backward using a star screwdriver (PH2). The rear housing should be adjusted so that the included spacer fits between the binding and the boot. Make sure there is no weight on the boot when making this adjustment.

Adjusting the Release Value

The release value is adjusted by turning the silver screw (PH2) on the top of the rear housing. The release scale is located on the back of the housing.

Using Walk Mode

Lock the ski brakes into walk mode using the lever on the right side of the binding. Rotate the rear housing 180 degrees so the pins face backward. Step into the front housing with your boot and pull the lever up on the front housing to engage walk mode. There are two heel lifters that can be flipped forward for use.

Using Ski Mode

Rotate the rear housing so the pins face forward. Press the lever on the right side of the binding to engage the ski mode. Step into the front housing with your boot. The lever should be in walk mode. Step hard into the rear housing to lock the boot in place.

Attaching Ski Crampons

To attach ski crampons, hold the crampon vertically on either the right or left side of the binding. Slide the crampon into place so it is centered on the ski. Then, lower the crampon flat onto the ski. To remove the crampon, reverse the process.

ATK Raider EVO and Freeraider EVO!

Coming soon!